treats rumpus plate for TJT variator - honda HOBBIT version
treats rumpus plate for TJT variator - STEEL
 
  $44.99

 :HERE NOW!!

Free Shipping
qty:

 
 
new for 2018 treatland presents the treatland treatland treatland ramp plate!! the ramp angles have been optimized for use with the TJT variator body. provides smoother variation throughout the range over the stamped TJT plate!

want the whole dang thing kit n caboodle?

this is the honda HOBBIT pa50-II camino specific version!!! if you try and use it on a derbi, it no work!

BUT If you have a pa50-I, use the derbi ramp plate because the pa50-I clutch bell is different, dude!

uses derbi ramp plate guides sold separately

if you are switching from a factory derbi 6 roller ramp plate, TJT ramp plate, or other 6 roller ramp plate you will need to go up or down slightly to fulfill your performance desires. In our experience you will usually be dropping weight.

You will probably also want to experiment with different contra springs to get the most out of your new setup.

the second photo is for illustrative purpose only, to be clear you just get the plate, not the whole variator or ramp plate guides!

may come in BLACK or RAW steel finish

taco rating taco rating 5 of 5 5 of 5 Total Reviews: 9 give your taco rating here

  0 taco eaters like this review
 
5 of 5 Like butter mixed with grease and lotion July 18, 2022
taco eater : Matt of RaBiEs from winnipeg, MB Canada  
Smooooooth.... super smooth... extra premium mega smooth... Legit though... this thing is smooth... did I say that yet? Buy extra weights to tune it... it basically makes variation with the TJT totally seamless and predictable. Honestly it might be too smooth...like, when something is so perfect and works so well it almost doesnt seem right on a moped.... that being said... If you want the smoothest variation you ever felt on a moped, this is the way...

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 Holy shidd August 5, 2021
taco eater : Marc B from New Orleans, LA United States  
This thing is just the thing you need if you’re in between weights or getting funky variation on your ripper. Went from the correct weights acting weird, to the smoothest variation i’ve ever had the pleasure of experiencing. Amazing piece of hardware for real. Be sure to chamfer the sharp inside edges to prolong your weight’s lyfe.

Was this review helpful to you?

  0 taco eaters like this review
 
3 of 5 RPM drop July 27, 2019
taco eater : roger suarez from APOPKA, FL United States  
Requires tweaking rear contra and weights. I experienced rpm drop and hence loss of staying in the power band compared to TJT plate.

15g+red= drop

Was this review helpful to you?

  1 taco eaters like this review
 
5 of 5 only works on PA50-II bell January 22, 2019
taco eater : eames  
Since this is made specifically for hobbits, it fits the Hobbit PA50-II bell PERFECTLY.  That is no more slop.  With that, if you were previously using a TJT with a PA50-I, it will no longer fit.

Just a heads up.  

edit: these can be easily modified for use on a pa50I bell with the use of a round file! you are correct though!

Was this review helpful to you?

  1 taco eaters like this review
 
5 of 5 Nicely done- a Must have! August 5, 2018
taco eater : Neil Burgess from Aberdeen, WA United States  
Works much better than the TJT plate. My Athena setup loves this plate at 12-13g total weight. TJT used to get all wonky at anything under 17g with the old plate... now the lighter ya go the better! This is exactly the part you want and need for a ripper hobbit.

setup: Athena, H95, del 21, TJT 12.3g total weight, red contra, stock gears

see a quick zero to 50 here: https://www.facebook.com/neil.burgess.969/videos/2295662637115527/

Was this review helpful to you?

View All Customer Reviews