6203 C3 crankshaft bearing for puch e50 + peugeot + derbi + garelli + tomos + solex
6203 C3 bearing
 
  $8.66

 :HERE NOW!!

Free Shipping
qty:

 
 
6203 C3 crankshaft bearing for rebuilding e50 (one speed) engines on any puch moped. also one of the bearings for peugeot engines, derbi flat reed and piston port/pyramid reed magneto side!!!!! tomos A35/A55 (oem#035070), garelli NOI +VIP (check NOI first! see note below), morini m1/m01/M02, yamaha QT50 (both sides), puch ZA50 output shaft and others like solex !!! ++ 1 of 2 honda nu50 transmission bearings (6202 is the other).

A total rebuild of your E50 will require 4 bearings - 3 of these and one 6203 NR. see here for more puch bearing sets

for garelli NOI you need 2 of these for just the crank or 4 for a full rebuild, take note though some garelli noi use a 16003 bearing and some use a 6203 apparently...check first !

brand wise we ONLY carry the highest quality c3 bearings! You will get either NSK, SKF, NTN or ZKL. we do not carry generic unmarked crappy bearings!

for garelli VIP you need 2 of these for the crank bearings, plus one more for the driveshaft if you like

take note! pre-1986 tomos A3 engines use L17 bearings NOT 6203!

bearings measurements:

17mm ID
40mm OD
12mm wide

taco rating taco rating 3.5 of 5 3.5 of 5 Total Reviews: 10 give your taco rating here

  2 taco eaters like this review
 
5 of 5 Treats needs to mention this!! June 18, 2021
taco eater : mark from United States  
YO!! TOMOS A3 PEOPLEZ! there are TWO different versions of your motor! the EARLY VERSION (ie silver covers and some very early black covers) use L17A CRANK BEARINGS! these ones (6203  C3) ONLY WORK FOR THE LATE VERSIONS!! (ie, very late-model black cases) MEASURE YOUR CASES BRUH!

Was this review helpful to you?

  1 taco eaters like this review
 
1 of 5 Not for Tomos A3 September 4, 2020
taco eater : Kevin Edwards from omaha, NE United States  
If you search for A3 crankshaft bearings the results all are 6203 C3. Which is the wrong size bearings The A3 uses L17 bearings on the crankshaft, 2 mm thinner

Was this review helpful to you?

  0 taco eaters like this review
 
5 of 5 umm March 24, 2016
taco eater : rodney from san francisco, CA  
used these on soo many e50's and derbi's ive built through the years and theyre a good inexpensive bearing to use. on each engine they have been in, put tons of miles on em

Was this review helpful to you?

  0 taco eaters like this review
 
2 of 5 I don't like 'em October 4, 2014
taco eater : Anonymous Person from Colorado  
Couple didn't spin well. Vinegar made them rust. Maybe I don't know what I'm doing, but this is the first time I've had issue with bearings like this.

Was this review helpful to you?

  0 taco eaters like this review
 
2 of 5 does not fit Garelli Noi April 25, 2014
taco eater : Eric Jaromin from Dahlonega, GA United States  
nice looking bearing, but does not fit a 76 Garelli Noi engine - they take the SKF 16003/c3 bearing...

edit benji : yepp see the info above, some garelli NOI use 16003/c3  and some use 6203 !!

Was this review helpful to you?

View All Customer Reviews