16mm honda hobbit pa50 clone carb

16mm-ish honda hobbit pa50 clone carb

$22.99

:HERE NOW!!

qty:

stock-like clone carb for honda hobbit pa50i pa50ii and camino! that's a nice lil upgrade in carburation! would be very interesting to see this on a sleeper build hmmm. scare your friends when u blast past lookin all stock like. hehehe

16mm diameter at the flange mount but the bore tapers down to about 12-13mm or so! so lets call it a 16:12.5mm carb.

in classic clone fashion be gentle with the float bowl, top cap and clamp bolts. the casting aluminum is a little on the weaker side.

uses standard hobbit main jets and comes with the classic clone carb no number jet.

comes with a piece of drain line not shown in the photo!!

***the drain screw may or may not work on this. its a $20 carb so what do ya really expect***

***no returns on this except new/unused, sorry dudes!***

taco rating taco rating 4.5 of 5

4.5 of 5 Total Reviews: 5 give your taco rating here

0 taco eaters like this review

Perfect	October 25, 2023
taco eater : Grant Hauersperger from Delaware , OH United States

I put a smaller jet in because mine is a stock 78 Hobbit, ran like a new one ! Didn’t have to adjust anything. Just a warning though, when I pulled the float bowl there was left over shavings in there, from the factory most likely. You would be wise to check this before installing.

Was this review helpful to you?

0 taco eaters like this review

Solid carb - and can't beat the price!	June 3, 2022
taco eater : Fitz from Clawson, MI United States

Spent hours fiddling with my OEM 1979 PA50I carb to no avail. But I saw this and $20 and 4 days later I'm zipping around again. It seems to run a little too rich so I'll need to pick up a smaller jet I think.

Was this review helpful to you?

0 taco eaters like this review

Meh	December 16, 2019
taco eater : E from NORTH ANDOVER, MA United States

Mehhhhh idkkk, I guess it works and all but this guy ran a lot richer than an oem carb. Same jet, same setup: this carb was so rich bike wouldnt move, oem carb ripped. Again probably nothing wrong with this carb but I opted to use my oem carb over this one

Was this review helpful to you?

0 taco eaters like this review

Question....	November 17, 2017
taco eater : Anonymous Person from Valdosta, GA United States

Does this fix on a Honda Express?

Was this review helpful to you?

8 taco eaters like this review

Attack of the Clones	April 28, 2017
taco eater : DrGeorgeTompson from Washington, DC United States

I like this carb cause it has an extra adjustment screw that I'm not entirely sure what it does. You see it there? on the opposite side of all the other adjusty bits? yeah that one!

It is a needle that i'm pretty sure goes into the emulsion tube or maybe chokes the amount of fuel getting fed into that left side hole when you look into the back of the carb. Is that choke fueling? beats me. who cares though, more adjustment is good.

Anyways, the finer things:

Mine came with no o-ring. Harbor Freight box of o-rings saves the day again.

The mentioned "not shown in the photo" drain line is about 40 feet long and melted on my proma in like 30 seconds cutting it to the proper length. A+

I would say the included jet is a 78.

Aluminum doesn't seem bad. I didn't break it yet and i made sure to hog dick the screws and nuts real good for science.

Had to scrape some casting defects out of the float bowl. no problem

With a name like Wabron, how could you not trust it?

Was this review helpful to you?

treatland